Teka-teki Silang validate Choise of VPN Topology, Device And Topologies

TEKA-TEKI SILANG

Jawaban: 
  1. Layer  2 forwarding protocol
  2. Data Encryption Standard
  3. Secure hash algorithmi
  4. Advanced Encryption Standard
  5. Diffiehellman
  6. RSA
  7. Generic Routing Encapsulation
  8. Layer 2 Tunneling Protocol
  9. 3 DES
  10. IPSEC
  11. PPTD
  12. Message Digests
Gambar:

Komentar

Posting Komentar

Postingan populer dari blog ini

Lab 4.2.5.5 Calculating a VLSM Addressing Scheme

Langkah 1: Memeriksa persyaratan jaringan Gunakan diagram topologi untuk menentukan jawaban atas pertanyaan di bawah ini. Ingat bahwa alamat IP akan  diperlukan untuk setiap LAN dan WAN interface. Berapa banyak subnet yang dibutuhkan?  Jawaban: 7 Berapa jumlah maksimum alamat IP yang dibutuhkan untuk satu subnet tunggal ? Jawaban: 55 Berapa banyak host alamat IP yang dibutuhkan untuk LAN terbesar?  Jawaban: 26 Berapa banyak host alamat IP yang diperlukan untuk LAN berikutnya terbesar? Jawaban: 20 Berapa banyak host alamat IP yang dibutuhkan untuk LAN terkecil?  Jawaban: 12 Berapa banyak host alamat IP yang dibutuhkan untuk setiap link WAN?  Jawaban: 2 masing masing, dengan total 6 Berapa jumlah total alamat IP host yang diperlukan untuk jaringan ini?  Jawaban: 119 Berapa jumlah total alamat IP host yang tersedia dalam jaringan 192.168.1.0/24? Jawaban:  254 Jika jaringan adalah subnetted untuk memberikan 7 subnet digunakan, bisa mengatasi persyaratan yang harus dipenuhi?   Jawab
Baca selengkapnya

Lab 7.3.3 Configuring and Testing the Rapid Spanning Tree Prototype

Task 1: Configure all devices Step 1: Configure S1 and S2 Configure the host name, access, and command mode passwords on each switch. Step 2: Configure interface VLAN 1 Configure the VLAN1 IP address and default gateway on each switch. Step 3: Configure FC-ASW-1 for server and end user VLANs VLAN Number VLAN Name 10 Servers 20 Users Step 4: Configure ProductionSW for server and end user VLANs VLAN Number VLAN Name 10 Servers 20 Users Step 5: Assign ports to VLANs on FC-ASW-1 FC-ASW-1# configure terminal FC-ASW-1(config)# interface Fa0/5 FC-ASW-1(config-if)# switchport mode access FC-ASW-1(config-if)# switchport access VLAN10 FC-ASW-1(config-if)# interface Fa0/6 FC-ASW-1(config-if)# switchport mode access FC-ASW-1(config-if)# switchport access VLAN20 Step 6: Assign ports to VLANs on ProductionSW ProductionSW# configure terminal ProductionSW(config)# interface Fa0/5 ProductionSW(config-if)# switchport mode access ProductionSW(config-if)# switchport access VLAN10 Production
Baca selengkapnya

Lab 5.2.3 Configuring RIPv2 with VLSM, and Default Route Propagation

Step 1: Connect the equipment. a. Connect Router3 to Router1 and Router2 with serial cables. b. Connect Router1’s Fa0/0 interface with a straight-through cable to Switch1’s Fa0/1 interface. c. Connect Router2’s Fa0/0 interface with a straight-through cable to Switch2’s Fa0/1 interface d. Connect PC1 to Switch1 and PC2 to Switch 2 with straight-through cables. e. Connect PC3 to Router3’s Fa0/0 interface with a crossover cable. f. Connect a PC with a console cable to perform configurations on the routers and switches. Step 2: Perform basic configurations on the routers. a. Establish a console session with Router1 and configure hostname, passwords, and interfaces as described in the table. Save the configuration. b. Establish a console session with Router2 and perform a similar configuration, using the addresses and other information from the table. Save the configuration. c. Establish a console session with Router3. Configure hostname, passwords, and interfaces according to the table.
Baca selengkapnya