Lab 7.2.5 Testing the FilmCompany Network

Step 1: Build the prototype network
  1. Select the necessary equipment and cables as specified in the Equipment section of the test plan.
  2. See your instructor for assistance in identifying the appropriate equipment.
  3. Using the topology diagram and IP address plan contained in the Design and Topology Diagram section of the test plan, connect and configure the prototype network.
  4. Following the procedures in the Test 1: Procedures section, console into one of the devices and verify that you can ping all of the other device addresses. If you are unsuccessful, verify each device configuration. Repeat the connectivity testing.
  5. Copy and paste the initial device configurations into a document using Notepad or a word processing program. Save or print the document to include with the completed test plan.

Step 2: Verify the functionality of the prototype network
Following the procedures in the Test 1: Procedures, execute the various commands and record the results of the testing.
Copy and paste the output of the various commands into a document using Notepad or a word processing program. Save or print the document to include with the completed test plan.
Step 3: Record the test results in the Results and Conclusions section of the test plan
Compare the results that you observed during the testing with the expected results listed in the Test 1: Expected Results and Success Criteria section.
Determine if the testing indicates that the network meets the success criteria. If it does, indicate that the test is successful.


Task 2: Perform Test 2: VLAN Configuration Test

Step 1: Configure the prototype network

Step 2: Verify the VLAN configuration design

Step 3: Record the test results in the Results and Conclusions section of the test plan


Task 3: Perform Test 3: VLAN Routing Test

Step 1: Configure the prototype network
a. Follow the steps you created in the Test 3: Procedures section of the test plan to configure the router to route between VLANs. 
b. Using the topology diagram shown in the Design and Topology Diagram section of the test plan, configure the appropriate router to route between the VLANs created in Task 2. 
c. Following the steps you listed in the Test 3: Procedures section, console into the switch that is directly connected to the router. Configure the link between the switch and the router as an 802.1q trunk link
and permit all VLANs across the trunk.
d. Console into the router and configure the router interface directly connected to the switch for 802.1q encapsulation.
e. Configure the router with the appropriate IP addresses for the various VLANs. Verify that the routes appear correctly in the routing table.
f. Copy and paste the initial device configurations into a document using Notepad or a word processing program. Save or print the document to include with the completed test plan.

Step 2: Verify the VLAN routing design
a. Verify that the PCs are configured to be in different VLANs and that the IP address configuration on the PCs is correct. Configure the IP addresses assigned to the router, in Step 1e, as the default gateway addresses for the PCs. Verify that the default gateway addresses are on the same networks as the addresses assigned to the PCs.
b. Following the procedures in the Test 3: Procedures, ping from PC1 to PC2. Copy and paste the results into a document using Notepad or a word processing program. Save or print the document to include with the completed test plan.
c. Execute the various show commands to verify that the routing is correct.
d. Record the results in the Test 3: Results and Conclusions section of the test plan.

Step 3: Record the test results in the Results and Conclusions section of the test plan
a. Compare the results that you observed during the testing with the expected results listed in the Test 3: Expected Results and Success Criteria section.
b. Determine if the testing indicates that the network meets the success criteria. If it does, indicate that the test is successful.

Step 4: Reflection
Was the prototype testing of the FilmCompany LAN design successful? Did having a test plan to work from help you organize your testing?

Komentar

Posting Komentar

Postingan populer dari blog ini

Lab 4.2.5.5 Calculating a VLSM Addressing Scheme

Langkah 1: Memeriksa persyaratan jaringan Gunakan diagram topologi untuk menentukan jawaban atas pertanyaan di bawah ini. Ingat bahwa alamat IP akan  diperlukan untuk setiap LAN dan WAN interface. Berapa banyak subnet yang dibutuhkan?  Jawaban: 7 Berapa jumlah maksimum alamat IP yang dibutuhkan untuk satu subnet tunggal ? Jawaban: 55 Berapa banyak host alamat IP yang dibutuhkan untuk LAN terbesar?  Jawaban: 26 Berapa banyak host alamat IP yang diperlukan untuk LAN berikutnya terbesar? Jawaban: 20 Berapa banyak host alamat IP yang dibutuhkan untuk LAN terkecil?  Jawaban: 12 Berapa banyak host alamat IP yang dibutuhkan untuk setiap link WAN?  Jawaban: 2 masing masing, dengan total 6 Berapa jumlah total alamat IP host yang diperlukan untuk jaringan ini?  Jawaban: 119 Berapa jumlah total alamat IP host yang tersedia dalam jaringan 192.168.1.0/24? Jawaban:  254 Jika jaringan adalah subnetted untuk memberikan 7 subnet digunakan, bisa mengatasi persyaratan yang harus dipenuhi?   Jawab
Baca selengkapnya

Lab 7.3.3 Configuring and Testing the Rapid Spanning Tree Prototype

Task 1: Configure all devices Step 1: Configure S1 and S2 Configure the host name, access, and command mode passwords on each switch. Step 2: Configure interface VLAN 1 Configure the VLAN1 IP address and default gateway on each switch. Step 3: Configure FC-ASW-1 for server and end user VLANs VLAN Number VLAN Name 10 Servers 20 Users Step 4: Configure ProductionSW for server and end user VLANs VLAN Number VLAN Name 10 Servers 20 Users Step 5: Assign ports to VLANs on FC-ASW-1 FC-ASW-1# configure terminal FC-ASW-1(config)# interface Fa0/5 FC-ASW-1(config-if)# switchport mode access FC-ASW-1(config-if)# switchport access VLAN10 FC-ASW-1(config-if)# interface Fa0/6 FC-ASW-1(config-if)# switchport mode access FC-ASW-1(config-if)# switchport access VLAN20 Step 6: Assign ports to VLANs on ProductionSW ProductionSW# configure terminal ProductionSW(config)# interface Fa0/5 ProductionSW(config-if)# switchport mode access ProductionSW(config-if)# switchport access VLAN10 Production
Baca selengkapnya

Lab 5.2.3 Configuring RIPv2 with VLSM, and Default Route Propagation

Step 1: Connect the equipment. a. Connect Router3 to Router1 and Router2 with serial cables. b. Connect Router1’s Fa0/0 interface with a straight-through cable to Switch1’s Fa0/1 interface. c. Connect Router2’s Fa0/0 interface with a straight-through cable to Switch2’s Fa0/1 interface d. Connect PC1 to Switch1 and PC2 to Switch 2 with straight-through cables. e. Connect PC3 to Router3’s Fa0/0 interface with a crossover cable. f. Connect a PC with a console cable to perform configurations on the routers and switches. Step 2: Perform basic configurations on the routers. a. Establish a console session with Router1 and configure hostname, passwords, and interfaces as described in the table. Save the configuration. b. Establish a console session with Router2 and perform a similar configuration, using the addresses and other information from the table. Save the configuration. c. Establish a console session with Router3. Configure hostname, passwords, and interfaces according to the table.
Baca selengkapnya