game mewarnai



Komentar

  1. Anonim28 Desember 2010 pukul 10.47

    bagusnya musiknya ga putus (stop) gitu aja (di loop). trus coba tambahin tombol slider utk volume
    liat scriptnya di http://www.babaflash.com/forum/showthread.php?t=1810

    BalasHapus

Posting Komentar

Postingan populer dari blog ini

Lab 5.2.3 Configuring RIPv2 with VLSM, and Default Route Propagation

Step 1: Connect the equipment. a. Connect Router3 to Router1 and Router2 with serial cables. b. Connect Router1’s Fa0/0 interface with a straight-through cable to Switch1’s Fa0/1 interface. c. Connect Router2’s Fa0/0 interface with a straight-through cable to Switch2’s Fa0/1 interface d. Connect PC1 to Switch1 and PC2 to Switch 2 with straight-through cables. e. Connect PC3 to Router3’s Fa0/0 interface with a crossover cable. f. Connect a PC with a console cable to perform configurations on the routers and switches. Step 2: Perform basic configurations on the routers. a. Establish a console session with Router1 and configure hostname, passwords, and interfaces as described in the table. Save the configuration. b. Establish a console session with Router2 and perform a similar configuration, using the addresses and other information from the table. Save the configuration. c. Establish a console session with Router3. Configure hostname, passwords, and interfaces according to the table.
Baca selengkapnya

Lab 4.5.5 Testing UTP Cables

Step 1: Set up the Fluke 620 LAN CableMeter a. On the Fluke 620 meter, turn the rotary switch selector on the tester to the WIRE MAP position. b. Press the SETUP button to enter the setup mode and observe the LCD screen on the tester.  Press the UP or DOWN arrow buttons until the desired cable type of UTP is selected. Press ENTER to accept that setting and go to the next one. Continue pressing the UP/DOWN arrows and pressing ENTER until the tester is set to the following cabling characteristics. Tester Option Desired Setting - UTP CABLE : UTP WIRING : 10BASE-T OR EIA/TIA 4PR CATEGORY: CATEGORY 5 WIRE SIZE: AWG 24 CAL TO CABLE? NO BEEPING: ON or OFF LCD CONTRAST: From 1 through 10 (brightest) c. Once the meter is set up, press the SETUP button to exit setup mode. Step 2: Test Cabling Procedure a. For each cable to be tested use the following procedure. Place one end of the cable into the RJ-45 jack labeled UTP/FTP on the tester. Place the other end of the cable into the RJ-4
Baca selengkapnya

Lab 4.2.5.5 Calculating a VLSM Addressing Scheme

Langkah 1: Memeriksa persyaratan jaringan Gunakan diagram topologi untuk menentukan jawaban atas pertanyaan di bawah ini. Ingat bahwa alamat IP akan  diperlukan untuk setiap LAN dan WAN interface. Berapa banyak subnet yang dibutuhkan?  Jawaban: 7 Berapa jumlah maksimum alamat IP yang dibutuhkan untuk satu subnet tunggal ? Jawaban: 55 Berapa banyak host alamat IP yang dibutuhkan untuk LAN terbesar?  Jawaban: 26 Berapa banyak host alamat IP yang diperlukan untuk LAN berikutnya terbesar? Jawaban: 20 Berapa banyak host alamat IP yang dibutuhkan untuk LAN terkecil?  Jawaban: 12 Berapa banyak host alamat IP yang dibutuhkan untuk setiap link WAN?  Jawaban: 2 masing masing, dengan total 6 Berapa jumlah total alamat IP host yang diperlukan untuk jaringan ini?  Jawaban: 119 Berapa jumlah total alamat IP host yang tersedia dalam jaringan 192.168.1.0/24? Jawaban:  254 Jika jaringan adalah subnetted untuk memberikan 7 subnet digunakan, bisa mengatasi persyaratan yang harus dipenuhi?   Jawab
Baca selengkapnya