Lab 3.5.2 IP Addresses and Network Communication

Step 5: Change IP address for PC2 
a. On PC2, go to the Control Panel, double click the Network Connections icon, and then right click the connected Local Area Connection icon. Choose Properties from the pull-down menu. 
b. Using the scroll bar in the Local Area Connection Properties window, scroll down to highlight Internet Protocol (TCP/IP). Click the Properties button. 
c. Change the logical IP address for PC2 from 192.168.1.2 to 192.168.2.2 and leave the subnet mask set to 255.255.255.0. On what network is PC2 now?
Jawaban : PC2 is now on the 192.168.2.0 network 
d. Click OK, which will close the Internet Protocol (TCP/IP) Properties window. Click the Close button to exit the Local Area Connection Properties window. 
e. Refer back to Step 3c. On what network is PC1? PC1 is still on the 192.168.1.0 network. 
f. The two PCs are still on the same physical Ethernet network. Are they on the same logical IP network? Jawaban: NO

Step 6: Test network connectivity between the 2 PCs 
a. On PC1, go to Start, then Run. Type cmd, and then click OK. A Window command prompt window will appear. 
b. At the > prompt, type ping 192.168.2.2 and press Enter. Was it successful? No Why or why not? 
Jawaban: Ya.Karena pemasangan dan konfigurasinya benar. 
c. What type of networking device would allow the PCs to communicate?
Jawaban : A router, if placed between the 2 PCs using proper cabling

Step 7: Change IP address for PC1 
a. Using the procedure previously described, change the logical IP address for PC1 from 192.168.1.1 to 192.168.2.99 and leave the subnet mask set to 255.255.255.0. On what network is PC1 now? 
Jawaban : Ya. PC1 is now on the 192.168.2.0 network 
b. Click OK, which will close the Internet Protocol (TCP/IP) Properties window. Click the Close button to exit the Local Area Connection Properties window. 
c. The two PCs are still on the same physical Ethernet network. Are they on the same logical IP network now? Jawaban: No.

Step 8: Test network connectivity between the 2 PCs 
a. On PC2, go to Start, then Run. Type cmd, and then click OK. A Window command prompt window will appear. 
b. At the > prompt, type ping 192.168.2.99 and press Enter. Was it successful? Yes Why or why not?
Jawaban : Ya .Karena masih dalam satu jaringan

Komentar

Posting Komentar

Postingan populer dari blog ini

Lab 5.2.3 Configuring RIPv2 with VLSM, and Default Route Propagation

Step 1: Connect the equipment. a. Connect Router3 to Router1 and Router2 with serial cables. b. Connect Router1’s Fa0/0 interface with a straight-through cable to Switch1’s Fa0/1 interface. c. Connect Router2’s Fa0/0 interface with a straight-through cable to Switch2’s Fa0/1 interface d. Connect PC1 to Switch1 and PC2 to Switch 2 with straight-through cables. e. Connect PC3 to Router3’s Fa0/0 interface with a crossover cable. f. Connect a PC with a console cable to perform configurations on the routers and switches. Step 2: Perform basic configurations on the routers. a. Establish a console session with Router1 and configure hostname, passwords, and interfaces as described in the table. Save the configuration. b. Establish a console session with Router2 and perform a similar configuration, using the addresses and other information from the table. Save the configuration. c. Establish a console session with Router3. Configure hostname, passwords, and interfaces according to the table.
Baca selengkapnya

Lab 4.5.5 Testing UTP Cables

Step 1: Set up the Fluke 620 LAN CableMeter a. On the Fluke 620 meter, turn the rotary switch selector on the tester to the WIRE MAP position. b. Press the SETUP button to enter the setup mode and observe the LCD screen on the tester.  Press the UP or DOWN arrow buttons until the desired cable type of UTP is selected. Press ENTER to accept that setting and go to the next one. Continue pressing the UP/DOWN arrows and pressing ENTER until the tester is set to the following cabling characteristics. Tester Option Desired Setting - UTP CABLE : UTP WIRING : 10BASE-T OR EIA/TIA 4PR CATEGORY: CATEGORY 5 WIRE SIZE: AWG 24 CAL TO CABLE? NO BEEPING: ON or OFF LCD CONTRAST: From 1 through 10 (brightest) c. Once the meter is set up, press the SETUP button to exit setup mode. Step 2: Test Cabling Procedure a. For each cable to be tested use the following procedure. Place one end of the cable into the RJ-45 jack labeled UTP/FTP on the tester. Place the other end of the cable into the RJ-4
Baca selengkapnya

Lab 4.2.5.5 Calculating a VLSM Addressing Scheme

Langkah 1: Memeriksa persyaratan jaringan Gunakan diagram topologi untuk menentukan jawaban atas pertanyaan di bawah ini. Ingat bahwa alamat IP akan  diperlukan untuk setiap LAN dan WAN interface. Berapa banyak subnet yang dibutuhkan?  Jawaban: 7 Berapa jumlah maksimum alamat IP yang dibutuhkan untuk satu subnet tunggal ? Jawaban: 55 Berapa banyak host alamat IP yang dibutuhkan untuk LAN terbesar?  Jawaban: 26 Berapa banyak host alamat IP yang diperlukan untuk LAN berikutnya terbesar? Jawaban: 20 Berapa banyak host alamat IP yang dibutuhkan untuk LAN terkecil?  Jawaban: 12 Berapa banyak host alamat IP yang dibutuhkan untuk setiap link WAN?  Jawaban: 2 masing masing, dengan total 6 Berapa jumlah total alamat IP host yang diperlukan untuk jaringan ini?  Jawaban: 119 Berapa jumlah total alamat IP host yang tersedia dalam jaringan 192.168.1.0/24? Jawaban:  254 Jika jaringan adalah subnetted untuk memberikan 7 subnet digunakan, bisa mengatasi persyaratan yang harus dipenuhi?   Jawab
Baca selengkapnya